The Southern Ocean Gas Exchange Experiment (SO GasEx) was a multi-agency field investigation that focused on quantifying gas transfer velocities within the marine air boundary layer. SO GasEx had one deployment during the austral fall of 2008 across the Southern Ocean. The NOAA Ronald. H Brown research vessel was equipped with several in situ and remote sensors to collect measurements of trace gases, aerosols, and ocean properties. Other water platforms such as drifting and moored buoys and an underwater surface vehicle (USV) were also deployed. SO GasEx was funded by NASA, NOAA, and NSF.
GasEx had two previous deployments in 1998 and 2001. Only the information for 2008 deployment is in this inventory since NASA only participated in that deployment.
Earth Science > Oceans > Ocean Temperature > Sea Surface Temperature
This data will be added in future versions
Earth Science > >
This data will be added in future versions.
Earth Science > Atmosphere > Atmospheric Radiation > Solar Irradiance
If instrument model information is not available, can use this instrument entry for temperature, pressues, wind speed, wind direction, humidity
Earth Science > >
If instrument name or model is not available but documents show that specific chemical compounds or constituents or their properties were observed, can use instrument entry. Examples include: CO, CO2, NO, NO2, N2O, HNO3, HNO4, OH, H2SO4, CH3CN, O3, H2O, halocarbons, VOCs, nitrates, aerosols (including CCN), aerosol optical properties, etc...
Earth Science > >
The Multibeam Echo Sounder System or MBES uses a sonar that produces an angular swath of beams to the port and starboard side in a single ping to effectively map a corridor with a width approximately 3-4 times the water depth. MBES consists of three instruments namely Teledyne Reson SeaBat 7160, Teledyne Reson SeaBat 7111, and Kongsberg EM 710. The OMG bathymetry survey was primarily conducted using multi-swath Multibeam Echo Sounder System (MBES) equipment and procedures.
Earth Science > Oceans > Bathymetry/seafloor Topography > Water Depth
The PAR (Photosynthetically Active Radiation) Sensor reports the Photosynthetic Photon Flux Density (PPFD), which corresponds to micromoles of photons per meter squared per second (μmol m-2 s-1). This is the power of electromagnetic radiation in the spectral range that is used by plants for photosynthesis (400–700 nm). It features a waterproof sensor head and can be used to measure PPFD from sunlight and electric light sources. This sensor is ideal for experiments investigating photosynthesis and primary productivity and can be used in many agricultural and environmental science applications.
If instrument mode or detailed specification information is not available, can use this entry for spectrometers of various types. A spectrometer is an instrument that measures a range of a characteristic for a given substance or wavelength. There are many different types of spectrometers. Some examples are mass spectrometers, spectrophotometers, and magnetic radiation spectrometers.
Rain gauges are ground-based instruments that provide in situ measurements of liquid precipitation amounts over a set time. There are multiple types of rain gauges that each collect and record data differently such as the tipping bucket rain gauge and weighing precipitation gauge. Rain gauges can be deployed in various locations due to their relatively small size and easy set-up and are typically colocated with other precipitation instruments such as disdrometers to provide more details about precipitation being collected such as precipitation rate and size distribution.
This description will be added in future versions.
Earth Science > Oceans > Ocean Waves
The High-Performance Liquid Chromatograph (HPLC) is an in situ ground-based analyzer that is used to separate and identify components within a sample of air or mixture. It achieves this by injecting a liquid within the sample causing different flow rates for each component as they flow out of the column. As each component exits the column, their concentrations are measured at a high resolution. In Earth science research, HPLC is typically used to determine various trace species in the atmosphere such as formaldehyde, hydrogen peroxide, and volatile organic compounds (VOCs). HPLC is commonly used for laboratory analysis and ground-based measurements, but it can be used for airborne measurements as well.
Conductivity, Temperature, and Depth (CTD) sensors are in situ instrument packages that are used to measure water depth, pressure, salinity, temperature, and density in the ocean. CTD sensors can be deployed on various water-based platforms such as autonomous underwater vehicles (AUVs), buoys, gliders, or research vessels. When deployed on a vessel, CTD sensors are typically attached to a rosette and then lowered to the seafloor to measure water properties. CTD sensors have a typical sampling rate of 30 Hz and can collect precise measurements for a specific water depth depending on the researcher's needs.
Earth Science > Oceans > Ocean Pressure > Water Pressure
Earth Science > Oceans > Bathymetry/seafloor Topography > Water Depth
Earth Science > Oceans > Ocean Temperature > Water Temperature
Earth Science > Oceans > Salinity/density
The Acoustic Doppler Current Profiler (ADCP) is an in situ acoustic sensor used to measure ocean currents. ADCP uses the Doppler effect to detect sound waves to provide measurements of the speed and direction of currents throughout the water column. ADCP can easily be mounted on different water platforms such as ships, buoys, and autonomous underwater vehicles (AUVs). It also can be deployed on the seafloor to provide profile measurements of ocean currents.
Conductivity, Temperature, and Depth (CTD) sensors are in situ instrument packages that are used to measure water depth, pressure, salinity, temperature, and density in the ocean. CTD sensors can be deployed on various water-based platforms such as autonomous underwater vehicles (AUVs), buoys, gliders, or research vessels. When deployed on a vessel, CTD sensors are typically attached to a rosette and then lowered to the seafloor to measure water properties. CTD sensors have a typical sampling rate of 30 Hz and can collect precise measurements for a specific water depth depending on the researcher's needs.
Earth Science > Oceans > Ocean Pressure > Water Pressure
Earth Science > Oceans > Bathymetry/seafloor Topography > Water Depth
Earth Science > Oceans > Ocean Temperature > Water Temperature
Earth Science > Oceans > Salinity/density
If instrument model information is not available, can use this instrument entry for temperature, pressues, wind speed, wind direction, humidity
Earth Science > >
The Acoustic Doppler Current Profiler (ADCP) is an in situ acoustic sensor used to measure ocean currents. ADCP uses the Doppler effect to detect sound waves to provide measurements of the speed and direction of currents throughout the water column. ADCP can easily be mounted on different water platforms such as ships, buoys, and autonomous underwater vehicles (AUVs). It also can be deployed on the seafloor to provide profile measurements of ocean currents.
If instrument name or model is not available but documents show that specific chemical compounds or constituents or their properties were observed, can use instrument entry. Examples include: CO, CO2, NO, NO2, N2O, HNO3, HNO4, OH, H2SO4, CH3CN, O3, H2O, halocarbons, VOCs, nitrates, aerosols (including CCN), aerosol optical properties, etc...
Conductivity, Temperature, and Depth (CTD) sensors are in situ instrument packages that are used to measure water depth, pressure, salinity, temperature, and density in the ocean. CTD sensors can be deployed on various water-based platforms such as autonomous underwater vehicles (AUVs), buoys, gliders, or research vessels. When deployed on a vessel, CTD sensors are typically attached to a rosette and then lowered to the seafloor to measure water properties. CTD sensors have a typical sampling rate of 30 Hz and can collect precise measurements for a specific water depth depending on the researcher's needs.
Earth Science > Oceans > Ocean Pressure > Water Pressure
Earth Science > Oceans > Bathymetry/seafloor Topography > Water Depth
Earth Science > Oceans > Ocean Temperature > Water Temperature
Earth Science > Oceans > Salinity/density
If instrument model information is not available, can use this instrument entry for temperature, pressues, wind speed, wind direction, humidity
Earth Science > >
The Acoustic Doppler Current Profiler (ADCP) is an in situ acoustic sensor used to measure ocean currents. ADCP uses the Doppler effect to detect sound waves to provide measurements of the speed and direction of currents throughout the water column. ADCP can easily be mounted on different water platforms such as ships, buoys, and autonomous underwater vehicles (AUVs). It also can be deployed on the seafloor to provide profile measurements of ocean currents.
Conductivity, Temperature, and Depth (CTD) sensors are in situ instrument packages that are used to measure water depth, pressure, salinity, temperature, and density in the ocean. CTD sensors can be deployed on various water-based platforms such as autonomous underwater vehicles (AUVs), buoys, gliders, or research vessels. When deployed on a vessel, CTD sensors are typically attached to a rosette and then lowered to the seafloor to measure water properties. CTD sensors have a typical sampling rate of 30 Hz and can collect precise measurements for a specific water depth depending on the researcher's needs.
Earth Science > Oceans > Ocean Pressure > Water Pressure
Earth Science > Oceans > Bathymetry/seafloor Topography > Water Depth
Earth Science > Oceans > Ocean Temperature > Water Temperature
Earth Science > Oceans > Salinity/density
If instrument model information is not available, can use this instrument entry for temperature, pressues, wind speed, wind direction, humidity
Earth Science > >
If instrument name or model is not available but documents show that specific chemical compounds or constituents or their properties were observed, can use instrument entry. Examples include: CO, CO2, NO, NO2, N2O, HNO3, HNO4, OH, H2SO4, CH3CN, O3, H2O, halocarbons, VOCs, nitrates, aerosols (including CCN), aerosol optical properties, etc...
Conductivity, Temperature, and Depth (CTD) sensors are in situ instrument packages that are used to measure water depth, pressure, salinity, temperature, and density in the ocean. CTD sensors can be deployed on various water-based platforms such as autonomous underwater vehicles (AUVs), buoys, gliders, or research vessels. When deployed on a vessel, CTD sensors are typically attached to a rosette and then lowered to the seafloor to measure water properties. CTD sensors have a typical sampling rate of 30 Hz and can collect precise measurements for a specific water depth depending on the researcher's needs.
Earth Science > Oceans > Ocean Pressure > Water Pressure
Earth Science > Oceans > Bathymetry/seafloor Topography > Water Depth
Earth Science > Oceans > Ocean Temperature > Water Temperature
Earth Science > Oceans > Salinity/density
If instrument name or model is not available but documents show that specific chemical compounds or constituents or their properties were observed, can use instrument entry. Examples include: CO, CO2, NO, NO2, N2O, HNO3, HNO4, OH, H2SO4, CH3CN, O3, H2O, halocarbons, VOCs, nitrates, aerosols (including CCN), aerosol optical properties, etc...
